platform.h
4.31 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
#ifndef _PLATFORM_H_
#define _PLATFORM_H_
#include "platform_interface.h"
#include "gd32f30x.h"
#include "core_cm4.h"
//临界保护，do{} while的写法确保成对出现，可防止代码光中断后忘记开中断
//__disable_irq()//
//__enable_irq();//
#define PLATFORM_DISABLE_IRQ() \
{ \
uint32_t LockState; \
LockState = __get_PRIMASK();\
__set_PRIMASK(1);
#define PLATFORM_ENABLE_IRQ() \
__set_PRIMASK(LockState); \
}
extern unsigned char rx_uart_buf;
extern volatile unsigned short _20ms_timer_count;
extern volatile unsigned char _0s5_flag;
extern volatile unsigned char mainloop_20ms_flag;//_20ms_flag;
extern volatile unsigned char mainloop_2ms5_flag;
/*
*检测当前的tcpip还是usb通信方式
*/
void set_pc_communication_type(unsigned char type);
unsigned char get_pc_communication_type(void);
////中断总开关
//extern void CLI(void);
//extern void SEI(void);
/*
2019.12.04 实测1ms;
环境：主频168MHz,关闭中断,IO取反用示波器测试!! */
void basic_delay_ms( unsigned short time );
/*
2019.12.04 实测 delay(500) =500us;
环境：主频168MHz,关闭中断,IO取反用示波器测试!!
由于GPIO无法响应 delayus(1)，所以实际测试delay(500) =500us */
void basic_delay_us( unsigned int time );
unsigned short CRC16(const unsigned char *ptr,unsigned char len);
unsigned char get_usb_status(void);
//buzzer ctrl;
void beep_ctrl(unsigned char mode);
//----------------LED --------------------------------
#define LED_NO1 1
#define LED_NO2 2
#define LED_NO3 3
#define LED_NO4 4
#define LED_STA_OFF 0
#define LED_STA_ON 1
#define LED_STA_TOG 2
void display_led_ctrl(unsigned char led_NO,unsigned char status);
//
//void led_init(void);
void led1_control(unsigned char type);
void led2_control(unsigned char type);
//i2c
void i2c_init( void );
void i2c_start(void);
void i2c_stop(void);
unsigned char i2c_send_byte(unsigned char byt);
unsigned char i2c_read_byte(void);
//e2prom
unsigned char EE_ReadBytes( unsigned int Addr, unsigned char Array[],unsigned char Len);
void EE_WriteBytes( unsigned int Addr , const unsigned char Array[], unsigned char Len);
//---------------------lcd --------------------------------
void lcd_init(void);
void lcd_back_light_ctrl( unsigned char on_off);
void display_chinese(unsigned short x,unsigned short y
//,unsigned char char_type
,const unsigned char *chr
,unsigned char len
//,unsigned char reverse
);
void display_char(unsigned short x,unsigned short y
//,unsigned char char_type
,const unsigned char *chr
//,unsigned char len
//,unsigned char reverse
);
//---------------------------- NFC--------------------
//rfid card
void rfid_init(void);
//unsigned char rfid_write_card(void);
unsigned char get_rfid_reader_Hard_connect_status(void);
int int nfc_write_read_N_block(struct nfc_app_STR *nfc) ;(struct nfc_app_STR *nfc) int nfc_write_read_N_block(struct nfc_app_STR *nfc) ;
unsigned char nfc_reader(unsigned char addr,unsigned char cnt,unsigned char *out) ;
//------------------------- RF --------------
void rf_Irq(unsigned char rf_id);
void rf_initial(unsigned char rf_id);
void rf_setfreq(unsigned char freq,unsigned char rf_id);
void rf_SendPacket( unsigned char* txbuf, unsigned char Length,unsigned char rf_id );
void rf_set_PA_Mode( unsigned char mode,unsigned char rf_id );
void A5130_send_data_sub(unsigned char *buf,unsigned char count,unsigned char rf_id);
void A5130_send_beacon(void (*send_function)(const unsigned char *,unsigned char id),const unsigned char *tmp,unsigned char rf_id );
//#if (SUPPORT_HS6621_SOC)
void rf_set_syncode(unsigned short sync,unsigned char sync_cnt,unsigned char rf_seq);
//#else
//void rf_set_syncode(unsigned short sync,unsigned char rf_id);
//#endif
void set_tx_ok_flag(unsigned char flag);
unsigned char get_tx_ok_flag(void);
void waitfor_tx_ok(void);
void uart1_send_datas(unsigned char *pt,unsigned short len);
/**/
void set_hard_flag(unsigned char h_flag);
unsigned char get_hard_flag(void);
#endif //_PLATFORM_H_